쉬프트 인텐시브 클리너
SHIFT Intensive Cleaner
Carbon Collective · Carbon Collective SHIFT Intensive Cleaner · CC SHIFT Intensive Cleaner · SIC · Carbon Collective SIC · CC SIC · 카본 콜렉티브 쉬프트 인텐시브 클리너 · 카본 콜렉티브 SIC
타르와 점착성 글루를 제거하기 위해 처음 개발된 솔벤트 베이스의 인텐시브 클리너로, 왁스 오일 언더실, 타이어 고무, 그리스, 엔진 오일, 누적된 오염물까지 함께 제거할 수 있도록 개량되었습니다. 오염 부위에 직접 분사한 뒤 잔여물이 풀어질 때까지 머물게 한 후 마이크로파이버로 닦아내거나 플라스틱 블레이드로 제거합니다. 차량 헤드라이트나 민감한 플라스틱에는 사용하지 마십시오.
- 브랜드
- 카본 콜렉티브
- 카테고리
- Exterior : Remover
- 기본 희석 비율
- RTU
핵심 특징
- 타르, 글루, 접착제 잔여물 제거
- 오래된 타이어 드레싱과 고무 잔여물 제거
- 휠 웨이트 글루 제거
- 엔진 베이의 그리스와 오일 분해
- 과도하게 도포된 왁스오일·언더실 제거
- 헤드라이트나 민감한 플라스틱에는 사용 금지
희석 비율
- Exterior : Remover — RTU (1:0) (기본)
사용법
- 본격 사용 전 눈에 띄지 않는 부위에서 호환성 테스트를 진행하고 작업 내내 장갑을 착용합니다.
- 타르 제거 시 직접 분사한 뒤 갈색 액체가 흘러내릴 때까지 잠시 두고, 깨끗한 마이크로파이버로 닦아내며 필요 시 반복합니다.
- 타이어 작업 시 마이크로파이버에 충분히 적셔 사이드월을 문지르고, 깨끗해질 때까지 액제를 다시 도포한 후 물로 헹굽니다.
- 휠 웨이트 글루 제거 시 표면에 분사한 뒤 스퀴지나 플라스틱 블레이드로 폼 백킹을 들어내고, 글루가 드러나면 다시 분사해 마이크로파이버로 닦아냅니다.
- 엔진 베이의 그리스에는 분사 후 1~2분 두고 필요 시 빳빳한 브러시로 어지테이션한 뒤 물로 헹궈 냅니다.
- 왁스오일이나 언더실은 해당 부위에 직접 분사한 후 마이크로파이버로 닦아내고, 원하는 상태가 될 때까지 반복합니다.
- 트랙 또는 타이어 고무 잔여물에는 직접 분사한 뒤 들어 올리듯 가볍게 닦아 내며 제거합니다.
A solvent-based intensive cleaner originally formulated to remove tar and adhesive glue, with the secondary capability to lift wax oil underseal, tyre rubber, grease, engine oil and built-up grime. Sprayed directly on the contamination, it dwells until the residue softens and is wiped or blade-removed depending on the substrate. Not for use on vehicle headlights or sensitive plastics.
Key features
- Removes tar, glue and adhesive residue
- Lifts old tyre dressings and rubber buildup
- Removes wheel weight glue
- Cuts through engine bay grease and oil
- Removes over-applied waxoyl and underseal
- Not for use on headlights or sensitive plastics
Usage
- Test a small inconspicuous area for compatibility before full application and wear gloves throughout.
- On tar, spray directly and dwell for a few seconds until brown liquid runs from the deposit, then wipe with a clean microfibre and repeat
- On tyres, saturate a microfibre cloth, rub across the sidewall, re-apply liquid until clean, and rinse with water.
- On wheel weight glue, spray onto the surface and lift the foam backing with a squeegee or plastic blade, then re-apply and wipe to remove
- On engine bay grease, spray onto the area, dwell for 1-2 minutes, agitate with a stiff bristle brush if needed, then rinse off.
- On waxoyl or underseal, spray directly on the affected area and wipe with a microfibre, repeating until the desired finish is achieved.
- On track or tyre rubber, spray directly and lightly wipe in a lifting motion until the rubber is removed.