SHIFT Intensive Cleaner
쉬프트 인텐시브 클리너
A solvent-based intensive cleaner originally formulated to remove tar and adhesive glue, with the secondary capability to lift wax oil underseal, tyre rubber, grease, engine oil and built-up grime. Sprayed directly on the contamination, it dwells until the residue softens and is wiped or blade-removed depending on the substrate. Not for use on vehicle headlights or sensitive plastics.
타르와 점착성 글루를 제거하기 위해 처음 개발된 솔벤트 베이스의 인텐시브 클리너로, 왁스 오일 언더실, 타이어 고무, 그리스, 엔진 오일, 누적된 오염물까지 함께 제거할 수 있도록 개량되었습니다. 오염 부위에 직접 분사한 뒤 잔여물이 풀어질 때까지 머물게 한 후 마이크로파이버로 닦아내거나 플라스틱 블레이드로 제거합니다. 차량 헤드라이트나 민감한 플라스틱에는 사용하지 마십시오.
- Brand
- Carbon Collective
- Categories
- Exterior : Remover, Exterior : Degreaser&Dewaxing
Key features
- Removes tar, glue and adhesive residue
- Lifts old tyre dressings and rubber buildup
- Removes wheel weight glue
- Cuts through engine bay grease and oil
- Removes over-applied waxoyl and underseal
- Not for use on headlights or sensitive plastics
Usage
- Test a small inconspicuous area for compatibility before full application and wear gloves throughout.
- On tar, spray directly and dwell for a few seconds until brown liquid runs from the deposit, then wipe with a clean microfibre and repeat as needed.
- On tyres, saturate a microfibre cloth, rub across the sidewall, re-apply liquid until clean, and rinse with water.
- On wheel weight glue, spray onto the surface and lift the foam backing with a squeegee or plastic blade, then re-apply and wipe to remove the glue.
- On engine bay grease, spray onto the area, dwell for 1-2 minutes, agitate with a stiff bristle brush if needed, then rinse off.
- On waxoyl or underseal, spray directly on the affected area and wipe with a microfibre, repeating until the desired finish is achieved.
- On track or tyre rubber, spray directly and lightly wipe in a lifting motion until the rubber is removed.
핵심 특징
- 타르, 글루, 접착제 잔여물 제거
- 오래된 타이어 드레싱과 고무 잔여물 제거
- 휠 웨이트 글루 제거
- 엔진 베이의 그리스와 오일 분해
- 과도하게 도포된 왁스오일·언더실 제거
- 헤드라이트나 민감한 플라스틱에는 사용 금지
사용법
- 본격 사용 전 눈에 띄지 않는 부위에서 호환성 테스트를 진행하고 작업 내내 장갑을 착용합니다.
- 타르 제거 시 직접 분사한 뒤 갈색 액체가 흘러내릴 때까지 잠시 두고, 깨끗한 마이크로파이버로 닦아내며 필요 시 반복합니다.
- 타이어 작업 시 마이크로파이버에 충분히 적셔 사이드월을 문지르고, 깨끗해질 때까지 액제를 다시 도포한 후 물로 헹굽니다.
- 휠 웨이트 글루 제거 시 표면에 분사한 뒤 스퀴지나 플라스틱 블레이드로 폼 백킹을 들어내고, 글루가 드러나면 다시 분사해 마이크로파이버로 닦아냅니다.
- 엔진 베이의 그리스에는 분사 후 1~2분 두고 필요 시 빳빳한 브러시로 어지테이션한 뒤 물로 헹궈 냅니다.
- 왁스오일이나 언더실은 해당 부위에 직접 분사한 후 마이크로파이버로 닦아내고, 원하는 상태가 될 때까지 반복합니다.
- 트랙 또는 타이어 고무 잔여물에는 직접 분사한 뒤 들어 올리듯 가볍게 닦아 내며 제거합니다.