SWAG METAL ONE STEP POLISH User Guide

SWAG METAL ONE STEP POLISH dilution ratio and pH specification chart

메탈 원 스텝 폴리시

SWAG METAL ONE STEP POLISH — Exterior : Polishes. See full specs and usage on the Find Your Detail product page: https://findyourdetail.io/products/swag/metal-one-step-polish

SWAG 메탈 원 스텝 폴리시 — Exterior : Polishes. 전체 사양·사용법은 Find Your Detail 제품 페이지에서 확인하세요: https://findyourdetail.io/products/swag/metal-one-step-polish

A medium-cut one-step compound for renovating the metal parts of a vehicle such as exhaust tips, rim edges and trim. PROGRESS ABRASIVE and LOW TEMP technologies combine a wide abrasive spread with a lubricated paste that carries heat away, so the metal stays cooler and the machine is easier to control. It removes moderate scratches, dullness and deposits, often in a single pass, and works by hand as well as on wool or foam pads.

배기 팁과 휠 림 가장자리, 트림 같은 차량 금속 부위를 되살리는 미디엄 컷 원스텝 컴파운드입니다. PROGRESS ABRASIVE와 LOW TEMP 기술이 넓은 입자 분포와 윤활성 있는 페이스트를 결합해 열을 빼내므로 금속 온도가 낮게 유지되고 기계 조작이 쉬워집니다. 중간 정도의 스크래치와 광택 저하, 침착물을 대개 한 번의 작업으로 정리하며 손 작업과 울·폼 패드 작업 모두 가능합니다.

Brand
SWAG
Categories
Exterior : Polishes
Last updated
2026-08-01

Key features

Usage

  1. Work in the shade on a cool, clean surface, shake the bottle and test on an inconspicuous area.
  2. By hand: dose a few drops onto a pad, applicator or microfiber cloth and work in small sections.
  3. By hand: polish in circular or linear motions to suit the part.
  4. By machine or drill: choose felt or pad hardness according to how much renovation is needed.
  5. Spread an even layer over a small working area and polish with moderate pressure until the paste is worked in.
  6. Let the metal cool if it becomes too hot.
  7. Follow the felt pad with a foam pad for the best final finish.
  8. Set the polisher to the optimal speed: up to 1500 RPM on a rotary polisher, or your preferred speed on a DA polisher.
  9. Inspect the finish and degrease the surface with SWAG FINAL INSPECT, repeating the process if any degradation remains.

핵심 특징

  • 금속용 중간 연마 입도
  • PROGRESS ABRASIVE 및 LOW TEMP 기술
  • 중간 스크래치와 광택 저하, 침착물 제거
  • 한 번의 작업으로 원스텝 복원
  • 손, 폴리셔, 드릴 모두 사용 가능
  • 배기 시스템, 림 가장자리, 트림용

사용법

  1. 그늘에서 서늘하고 깨끗한 표면에 작업하며 용기를 흔들고 눈에 띄지 않는 부위에서 먼저 시험합니다.
  2. 손 작업: 패드나 어플리케이터, 마이크로파이버에 몇 방울을 덜어 좁은 구획씩 작업합니다.
  3. 손 작업: 부위에 따라 원을 그리거나 직선으로 문지릅니다.
  4. 기계·드릴 작업: 필요한 복원 강도에 맞춰 펠트나 패드 경도를 고릅니다.
  5. 좁은 작업 면적에 균일하게 펴 바르고 적당한 압력으로 페이스트가 다 먹을 때까지 연마합니다.
  6. 금속이 과열되면 식을 때까지 기다립니다.
  7. 펠트 패드 작업 후 폼 패드로 마무리하면 마감이 가장 좋습니다.
  8. 폴리셔 속도를 맞춥니다: 로터리 폴리셔는 최대 1500RPM, DA 폴리셔는 원하는 속도로 설정합니다.
  9. 마감 상태를 점검하며 SWAG FINAL INSPECT로 표면을 탈지하고, 흠집이 남아 있으면 과정을 반복합니다.

Also known as: 스웨그, 스웩, Swag METAL ONE STEP POLISH, SPMOSP, Swag SPMOSP, 스웨그 메탈 원 스텝 폴리시, 스웨그 SPMOSP

한국어로 보기

Sources

Related products

More from SWAG

More Polishes products

Explore more