Flat Top
플랫 탑
Flat Top is an aggressive cutting compound featuring triple-filtered agglomerates — abrasives that have undergone a tumbling and purification process three times to produce smooth, refined edges. This allows the compound to cut hard clear coats efficiently while finishing down to a near-mirror result, eliminating the need for a dedicated finishing polish in many cases. The dry emulsion formulation enables fast cycle times and effortless wipe-off.
플랫 탑은 3중 여과된 응집 연마재를 사용한 강력한 컷팅 컴파운드로, 연마 입자를 텀블링·정제 공정을 세 차례 거쳐 가공해 매끄럽고 정밀한 엣지를 형성합니다. 이를 통해 경질 클리어 코트를 효율적으로 제거하면서도 거울에 가까운 광택으로 마무리되어, 별도의 마무리 폴리시 없이 작업을 완결할 수 있습니다. 건식 에멀션 방식으로 짧은 작업 시간과 손쉬운 잔여물 제거가 가능합니다.
- Brand
- Shine Supply
- Categories
- Exterior : Polishes
- pH
- neutral (8)
Key features
- Triple-filtered agglomerate abrasives
- Aggressive cut with mirror-finish capability
- Short cycle time for faster productivity
- Dry emulsion for effortless wipe-off
- Works with any DA polisher
- Safe on all paint types and clear coats
- Semi-odorless, low-toxicity solvent
Usage
- Prime the microfiber pad with an outer and inner circle of product, then rub it thoroughly into the pad surface.
- Before turning on the polisher, spread the product evenly over a 2ft × 2ft area. Set the dual action polisher to speed 5 and make 2 slow passes with moderate pressure.
- Blow out the pad with compressed air or use a pad cleaning tool. Apply 4 dime-sized dots of product and make 2 more passes with zero downward pressure to allow maximum backing plate rotation.
- Wipe the surface clean with a microfiber towel, then follow with Classic Polish or Slick Back primer polish.
- For foam cutting pads, skip the outer/inner circle priming and use 4 dime-sized dots instead.
핵심 특징
- 3중 여과 응집 연마 입자
- 강력한 컷팅과 거울 광택 동시 구현
- 짧은 작업 사이클로 빠른 생산성
- 건식 에멀션으로 잔여물 제거 용이
- 모든 더블 액션 폴리셔 호환
- 모든 도장 유형 및 클리어 코트에 안전
- 반무취·저독성 용제 사용
사용법
- 마이크로파이버 패드에 제품을 바깥쪽과 안쪽 원 모양으로 도포한 후 패드 표면에 충분히 문질러 스며들게 합니다.
- 폴리셔를 켜기 전에 약 60×60cm 작업 면적에 제품을 고르게 펴 바릅니다. 더블 액션 폴리셔를 속도 5로 설정하고 적당한 압력으로 2회 천천히 패스합니다.
- 압축 공기나 패드 클리닝 도구로 패드를 털어냅니다. 동전 크기 4개 분량의 제품을 추가 도포하고 압력 없이 2회 더 패스하여 배킹 플레이트가 최대 회전수로 작동하게 합니다.
- 마이크로파이버 타월로 표면을 깨끗이 닦아낸 후 Classic Polish 또는 Slick Back 프라이머 폴리시로 마무리합니다.
- 폼 컷팅 패드 사용 시에는 바깥쪽/안쪽 원 모양 프라이밍을 생략하고 동전 크기 4개 분량의 제품으로 패드를 준비합니다.