플랫 탑
Flat Top
샤인 서플라이 · Shine Supply Flat Top · Shine Flat Top · SS Flat Top · FT · Shine Supply FT · Shine FT · SS FT · 샤인 서플라이 플랫 탑 · 샤인 서플라이 FT
3중 여과된 응집 연마재를 사용한 강력한 컷팅 컴파운드로, 연마 입자를 텀블링·정제 공정을 세 차례 거쳐 매끄럽고 정밀한 엣지로 가공합니다. 덕분에 경질 클리어 코트를 효율적으로 절삭하면서 거울에 가까운 광택으로 마무리되어, 별도의 마무리 폴리시가 필요 없는 경우가 많습니다. 건식 에멀션 방식으로 짧은 작업 시간과 손쉬운 잔여물 제거가 가능합니다.
- 브랜드
- Shine Supply
- 카테고리
- Exterior : Polishes
- 기본 희석 비율
- RTU
- pH
- neutral (8)
핵심 특징
- 3중 여과 응집 연마 입자
- 강한 컷팅과 거울에 가까운 광택
- 짧은 작업 사이클
- 건식 에멀션으로 잔여물 제거 용이
- 모든 더블 액션 폴리셔 호환
- 모든 도장 유형·클리어 코트에 안전
- 반무취·저독성 용제
희석 비율
- Exterior : Polishes — RTU (1:0) (기본)
사용법
- 마이크로파이버 패드에 제품을 바깥쪽·안쪽 원 모양으로 도포한 뒤 패드 표면에 충분히 문질러 스며들게 합니다.
- 폴리셔를 켜기 전에 약 60x60cm 면적에 제품을 고르게 펴 바르고, 더블 액션 폴리셔를 속도 5로 설정해 적당한 압력으로 2회 천천히 패스합니다.
- 압축 공기나 패드 클리닝 도구로 패드를 털고, 동전 크기 4개 분량을 추가 도포한 뒤 압력 없이 2회 더 패스해 배킹 플레이트가 최대 회전하도록 합니다.
- 마이크로파이버 타월로 표면을 깨끗이 닦은 뒤 Classic Polish 또는 Slick Back 프라이머 폴리시로 마무리합니다.
- 폼 컷팅 패드 사용 시에는 바깥쪽/안쪽 원 모양 프라이밍을 생략하고 동전 크기 4개 분량으로 패드를 준비합니다.
An aggressive cutting compound built on triple-filtered agglomerates, abrasives put through a tumbling and purification process three times for smooth, refined edges. This lets it cut hard clear coats efficiently while finishing down to a near-mirror result, so a separate finishing polish is often unnecessary. The dry emulsion formula allows fast cycle times and easy wipe-off.
Key features
- Triple-filtered agglomerate abrasives
- Aggressive cut with near-mirror finish
- Short cycle time
- Dry emulsion for easy wipe-off
- Works with any DA polisher
- Safe on all paint types and clear coats
- Semi-odorless, low-toxicity solvent
Usage
- Prime the microfiber pad with an outer and inner circle of product, then rub it thoroughly into the pad surface.
- Before turning on the polisher, spread the product evenly over a 2ft x 2ft area, set the dual action polisher to speed 5, and make 2 slow passes with moderate pressure.
- Blow out the pad with compressed air or a pad cleaning tool, apply 4 dime-sized dots of product, and make 2 more passes with zero downward pressure for maximum backing plate rotation.
- Wipe the surface clean with a microfiber towel, then follow with Classic Polish or Slick Back primer polish.
- For foam cutting pads, skip the outer/inner circle priming and use 4 dime-sized dots instead.