Beadlock Marine
비드락 마린
Beadlock Marine is a highly concentrated SiO2 ceramic coating engineered for watercraft, offering a hard sacrificial barrier against UV exposure, humidity, and harsh marine conditions. Its 2.5x greater concentration versus standard Beadlock Pro allows single-coat coverage on gel coat, boat bumper rails, painted metal, and clear plastic surfaces. The cured coating delivers over 9H hardness, a 110° water contact angle, and up to two years of aquatic durability.
비드락 마린은 선박용으로 설계된 고농축 SiO2 세라믹 코팅으로, 자외선·습기·가혹한 해양 환경으로부터 선체를 보호하는 희생 장벽을 형성합니다. 일반 비드락 프로보다 2.5배 높은 농도 덕분에 젤 코트, 범퍼 레일, 도장 금속, 클리어 플라스틱 등에 단일 레이어 도포가 가능합니다. 경화 후 9H 이상의 경도와 110° 접촉각을 달성하며 최대 2년간 수중 내구성을 유지합니다.
- Brand
- Shine Supply
- Categories
- Exterior : Coating
Key features
- SiO2 ceramic technology harder and more hydrophobic than wax or sealant
- 2.5x more concentrated than Beadlock Pro for single-coat application
- Hardness greater than 9H after cure
- 110° water contact angle
- pH resistance range of 2–13
- Up to 2 years aquatic durability
- Compatible with gel coat, metal, glass, and clear plastic surfaces
Usage
- Prep the surface by wiping it down with a paint cleanser to remove any oils or residue from prior polishing.
- If needed, polish the surface to reduce defects and maximize gloss, then wipe again with paint cleanser.
- Shake the bottle well, then apply directly onto an applicator pad and spread evenly over the surface.
- Allow a minimum of 60 seconds for the coating to begin setting up — an oil-slick rainbow effect will appear as it dries.
- Perform a test wipe with a clean microfiber towel; when slight resistance is felt, the coating is ready for removal.
- Remove the coating using a clean microfiber towel, then lightly pass a second towel to level the surface — do not re-wipe the area after it begins to set.
- Allow the coating to cure fully for 48 hours; avoid water contact during this period if possible.
핵심 특징
- 왁스나 실란트보다 강력한 SiO2 세라믹 기술
- 비드락 프로 대비 2.5배 고농축으로 단일 레이어 도포 가능
- 경화 후 9H 이상의 경도
- 110° 물방울 맺힘 접촉각
- pH 2–13 내산·내알칼리 저항성
- 최대 2년의 수중 내구성
- 젤 코트, 금속, 유리, 클리어 플라스틱 적용 가능
사용법
- 도장 클렌저로 표면을 닦아 폴리싱 후 남은 기름기나 잔여물을 제거합니다.
- 필요하다면 표면을 폴리싱하여 결함을 줄이고 광택을 극대화한 뒤, 도장 클렌저로 다시 닦아냅니다.
- 제품을 충분히 흔든 다음 어플리케이터 패드에 직접 적량을 덜어 표면에 고르게 도포합니다.
- 코팅이 건조되면서 오일 슬릭(무지개빛) 효과가 나타납니다. 최소 60초간 자연 경화를 기다립니다.
- 깨끗한 마이크로파이버 타월로 테스트 와이프를 해보아 약간의 저항감이 느껴지면 제거 준비가 된 것입니다.
- 깨끗한 마이크로파이버 타월로 코팅을 닦아내고, 두 번째 타월로 가볍게 한 번 더 정리합니다. 코팅이 세팅되기 시작한 후에는 다시 닦지 마십시오.
- 코팅이 완전히 경화되는 데 48시간이 소요됩니다. 가능하면 이 기간 중 물 접촉을 피하십시오.