servFaces 세라믹 코트 림스 매트 희석비 & 사용 가이드

servFaces 세라믹 코트 림스 매트 희석비 pH 스펙 카드

Ceramic Coat Rims Matt

휠 표면을 반광으로 마감하는 투명 고강도 세라믹 코팅으로, 도장 및 비도장 림에 모두 사용합니다. 오염에 강한 내구성 피막을 만들고 최대 +1050C의 열을 견디며, 특수 수지가 브레이크 오일로 인한 손상을 막아 줍니다. 최대 8um 두께로 유연하게 밀착되어 박리나 탈락이 없습니다.

브랜드
servFaces
카테고리
Exterior : Tire&Wheel Sealant
기본 희석 비율
RTU
최종 업데이트
2026-06-02

핵심 특징

희석 비율

용도희석비율
Exterior : Tire&Wheel Sealant (기본)RTU1:0

사용법

  1. Surface Cleaner Ultima로 표면을 세정한 후 Surface Cleaner Neutra로 중화합니다.
  2. 어플리케이터 블록에 도포용 천을 올려 놓습니다.
  3. 천에 제품을 12~18방울 떨어뜨린 뒤, 최대 50×50cm 구획으로 나눠 눈에 보이는 피막이 생길 때까지 빠르게 펴 바릅니다.
  4. 습도와 온도에 따라 약 1~3분간 건조시킵니다.
  5. Special Coating Towel로 가장자리부터 중앙 방향으로 직선 동작을 이용해 잉여 제품을 제거합니다.
  6. 새로운 Special Coating Towel로 가장자리부터 중앙 방향으로 원형 동작을 이용해 가볍게 버핑합니다.
  7. 얼룩이 남아 있으면 새 타월로 반복하고, 광원으로 확인하면서 작업합니다.
  8. 재코팅은 20분 후 가능하며, 35분 이내에 완료해야 합니다.

A transparent, high-strength ceramic coating that gives wheels a semi-gloss finish on painted and unpainted rims. It builds a durable, dirt-resistant film rated to withstand heat up to +1050C and shields against brake-fluid attack through its special resin. The flexible layer bonds at up to 8 um without chipping or peeling.

Key features

  • Semi-gloss finish for painted and unpainted rims
  • Heat resistance up to +1050C
  • Brake-fluid resistance from special resin
  • Flexible film up to 8 um without chipping or peeling
  • Not removable by conventional cleaners
  • Long-lasting dirt-resistant film
  • Low product consumption

Usage

  1. Clean the surface with Surface Cleaner Ultima, then neutralize with Surface Cleaner Neutra.
  2. Place the application cloth onto the applicator block.
  3. Apply 12–18 drops of product onto the cloth and spread quickly across the surface in sections of max. 50×50 cm until a visible film forms.
  4. Allow to dry for approximately 1–3 minutes, adjusting for humidity and temperature.
  5. Remove excess material with a Special Coating Towel, working from the edges inward using straight, swift motions.
  6. Buff with a fresh Special Coating Towel using light circular pressure, working from edges inward.
  7. If streaks remain, use another clean towel and repeat until the surface is clear (verify with a light source).
  8. Recoating is possible after 20 minutes but must be completed within 35 minutes.

다른 이름: serv, 서브페이스, 서브, servFaces Ceramic Coat Rims Matt, SF Ceramic Coat Rims Matt, CCRM, servFaces CCRM, SF CCRM, 서브페이시스 세라믹 코트 림스 매트, SF10182.2

View in English

출처

관련 제품

servFaces의 다른 제품

같은 카테고리(Tire&Wheel Sealant) 제품

더 보기