Ceramic Coat Rims
세라믹 코트 림스
serv · 서브페이스 · 서브 · servFaces Ceramic Coat Rims · SF Ceramic Coat Rims · CCR · servFaces CCR · SF CCR · 서브페이시스 세라믹 코트 림스 · SF10006.1
Ceramic Coat Rims is a clear, high-strength ceramic coating made specifically for rim surfaces on any vehicle. It forms a durable film that resists dirt, repels brake fluid, and handles temperatures up to +1050°C. The flexible film bonds firmly at up to 8 µm, so it will not chip or peel.
세라믹 코트 림스는 모든 차량의 휠 표면을 위해 만든 투명 고강도 세라믹 코팅입니다. 오염에 강하고 브레이크 오일을 막으며 최대 +1050°C까지 견디는 내구성 막을 형성합니다. 최대 8µm 두께로 유연하게 밀착되어 박리나 탈락이 생기지 않습니다.
- Brand
- servFaces
- Categories
- Exterior : Tire&Wheel Sealant
Key features
- For painted and unpainted rim surfaces
- Strong gloss enhancement
- Temperature resistance up to +1050°C
- Brake-fluid resistant via special resin
- Flexible film up to 8 µm with no chipping or peeling
- Not removable by conventional cleaners
- Low product consumption
Usage
- Clean the surface with Surface Cleaner Ultima, then neutralize with Surface Cleaner Neutra.
- Place the application cloth onto the applicator block.
- Apply 12 to 18 drops onto the cloth and spread quickly in sections of up to 50x50 cm until a film forms.
- Let it flash for about 1 to 3 minutes, adjusting for humidity and temperature.
- Remove excess with a Special Coating Towel, working from the edges inward in straight, swift strokes.
- Buff with a fresh Special Coating Towel using light circular pressure from edges inward.
- If streaks remain, repeat with another clean towel and check under a light source.
- Recoating is possible after 20 minutes but should be finished within 35 minutes.
핵심 특징
- 도장 및 비도장 림 표면 적용
- 강한 광택 향상
- 최대 +1050°C 내열
- 특수 수지로 브레이크 오일 저항
- 최대 8µm 유연 피막, 박리 없음
- 일반 세정제로 제거 불가
- 적은 제품 사용량
사용법
- 서피스 클리너 울티마로 표면을 세정한 뒤 서피스 클리너 뉴트라로 중화합니다.
- 도포용 천을 어플리케이터 블록에 올립니다.
- 천에 제품을 12~18방울 떨어뜨려 최대 50x50cm 구획으로 나눠 피막이 보일 때까지 빠르게 펴 바릅니다.
- 습도와 온도에 맞춰 약 1~3분간 둡니다.
- 스페셜 코팅 타월로 가장자리에서 중앙으로 직선 동작을 써서 잔여물을 제거합니다.
- 새 스페셜 코팅 타월로 가장자리에서 중앙으로 가볍게 원을 그리며 버핑합니다.
- 얼룩이 남으면 새 타월로 반복하고 광원으로 확인합니다.
- 재코팅은 20분 후 가능하며 35분 이내에 마칩니다.