BLINDO PLUS + HPC PRO - Ceramic Coating
블린도 플러스 + HPC 프로 - 세라믹 코팅
This is a two step ceramic coating set that pairs the resin based BLINDO PLUS base with the hybrid polysilazane HPC PRO top coat. The base layer is built for hardness and self curing without UV lamps while the top coat adds slick gloss and hydrophobic shedding. Together they target long term protection up to about 48 months or about 60,000 km.
BLINDO PLUS와 HPC PRO를 함께 시공하는 2단계 세라믹 코팅 시스템으로, 레진 기반의 BLINDO PLUS가 베이스 층을 구성하고 하이브리드 폴리실라잔 계열의 HPC PRO가 탑 코트를 담당합니다. 베이스는 단단함과 UV 램프가 필요 없는 자가 경화 특성을 갖추며 탑 코트는 미끌거리는 광택과 발수 성능을 더해줍니다. 이 조합은 약 48개월 또는 약 60,000km 정도까지의 장기 보호를 목표로 합니다.
- Brand
- Labocosmetica
- Categories
- Exterior : Coating
Key features
- BLINDO PLUS resin base for a hard barrier
- Nano Link bonding to the paint
- Self curing without UV lamps even in cooler conditions
- Deep, candy like base gloss
- HPC PRO top coat for hydrophobic durability up to about 48 months or 60,000 km
- Slick, glossy top layer with extra colour depth
- Outdoor friendly Dust Out Technology
- Forgiving correction window during install
- HPC PRO usable as standalone coating or top coat
Usage
- Decontaminate with SIDERO, polish if needed, and degrease with VERITAS before working below about 25 C and out of direct sun.
- Apply BLINDO PLUS first with 2 to 3 drops per panel in a criss cross pattern, wait for the flash, and level with a clean microfiber.
- After the recommended wait, lay HPC PRO over the base in a criss cross pattern, allow it to flash, then level and buff with a clean microfiber.
- Keep the vehicle away from water for at least about 12 hours and treat full cure as around 24 hours.
핵심 특징
- BLINDO PLUS 레진 베이스가 단단한 보호층을 형성
- 도장과 강하게 결합하는 나노 링크 기술
- UV 램프 없이도 저온에서 자가 경화
- 캔디처럼 깊이감 있는 베이스 광택
- HPC PRO 탑 코트로 약 48개월 또는 60,000km까지 발수 내구성
- 미끌거리는 탑 코트와 컬러 깊이 강화
- 실외 시공도 가능한 더스트 아웃 기술
- 시공 중 오류 보정이 가능한 여유 시간
- HPC PRO는 단독 코팅 또는 탑 코트로 사용 가능
사용법
- SIDERO로 탈오염하고 필요하면 폴리싱한 뒤 VERITAS로 탈지하며, 약 25도 이하에서 직사광선을 피해 작업합니다.
- 먼저 BLINDO PLUS를 패널당 2~3방울 크로스 해칭으로 도포하고 플래시 타임 후 깨끗한 마이크로파이버로 레벨링합니다.
- 권장 대기 시간이 지나면 HPC PRO를 베이스 위에 크로스 해칭으로 도포하고 플래시 후 마이크로파이버로 레벨링·버핑합니다.
- 최소 약 12시간 동안은 물을 피하고 완전 경화는 약 24시간 정도로 두는 것이 좋습니다.