A1 All In One
A1 올인원
innova · 이노바 · 이노바카 · Innovacar A1 All In One · IC A1 All In One · A1AIO · Innovacar A1AIO · IC A1AIO · 에이원 올인원 · 이노바카 에이원 올인원 · 이노바카 A1AIO · 79185
A silicone-free intermediate polish that handles correction, polishing, and finishing in one product. Its layered grain starts coarse and breaks down under friction into finer particles, so it can remove defects and bring up gloss in a single pass with rotary or rotary-orbital polishers.
교정·광택·마무리를 한 제품으로 처리하는 실리콘 미함유 중간 단계 광택제입니다. 계층형 입자가 처음에는 거칠다가 마찰로 더 미세하게 분해되어, 회전식·회전 궤도식 광택기로 한 번에 결함 제거와 광택을 함께 낼 수 있습니다.
- Brand
- Innova Car
- Categories
- Exterior : Polishes
Key features
- Correction, polishing, and finishing in one product
- Layered grain for progressive abrasive action
- Removes scratches, oxidation, and holograms
- Silicone-free, suitable before coating
- Works with rotary and rotary-orbital polishers
- Reduces and can remove sanding marks up to 2000 grit
Usage
- Finish all pre-polishing steps: pre-wash, wash, and chemical and mechanical decontamination.
- Shake the product well before use.
- Fit the right pad to the plate (medium-hard orange for cutting, medium-soft blue for finishing) and check it is centred and secure.
- Apply product to the pad without excess; new pads need more, used pads must be clean.
- Drape the cable over your shoulder, set the pad on the surface before switching on, and polish a 60x40 cm area at 800 rpm, first horizontally then vertically.
- Raise the speed toward 2000 rpm and re-treat the area for a uniform result.
- Remove excess with a microfibre cloth, check the result with D2 Check, then move to the next area.
- For the best finish, follow with P1 Polish Up.
핵심 특징
- 교정·광택·마무리를 하나로 통합
- 단계적 연마를 위한 계층형 입자
- 스크래치·산화·홀로그램 제거
- 실리콘 미함유, 코팅 전 사용 가능
- 회전식·회전 궤도식 광택기 호환
- 2000방까지의 샌딩 자국 감소·제거
사용법
- 프리워시·세차·화학적·기계적 오염 제거 등 폴리싱 전 단계를 모두 마칩니다.
- 사용 전 제품을 충분히 흔듭니다.
- 플레이트에 맞는 패드를 끼웁니다(컷팅용 중경질 오렌지, 마무리용 중연질 블루). 중심과 고정 상태를 확인합니다.
- 패드에 적당량을 도포합니다. 새 패드는 더 많이, 사용 패드는 깨끗해야 합니다.
- 케이블을 어깨에 걸고 패드를 표면에 댄 채 전원을 켜 800 rpm으로 60x40 cm 구역을 수평·수직으로 작업합니다.
- 속도를 2000 rpm까지 올리며 같은 구역을 다시 작업해 균일하게 다듬습니다.
- 마이크로파이버 천으로 잔여물을 제거하고 D2 체크로 결과를 확인한 뒤 다음 구역으로 넘어갑니다.
- 마무리를 위해 P1 폴리시 업으로 이어 작업합니다.