Cerberus V2 Ceramic Coating
케르베로스 V2 세라믹 코팅
Cerberus V2 is a highly durable nano-ceramic coating formulated to protect vehicle paintwork against UV exposure, chemical agents and minor surface scratches. It bonds firmly to the paint surface to deliver up to about 3 years of protection with a high-gloss, strongly hydrophobic finish, 7H hardness and chemical resistance across pH 2 to 11. Compared to the original version, V2 delivers greater coating thickness, hardness, depth of gloss and surface slickness.
케르베로스 V2는 자동차 도장면을 UV, 화학 약품, 미세 스크래치로부터 보호하도록 설계된 고내구성 나노 세라믹 코팅입니다. 도장면에 강하게 결합해 최대 약 3년간 하이그로스·하이드로포빅 마감과 7H 경도, pH 2~11 화학 저항성을 제공합니다. 이전 버전과 비교해 코팅 두께, 경도, 광택 깊이, 표면 슬릭함이 모두 향상되었습니다.
- Brand
- Garage Therapy
- Categories
- Exterior : Coating
Key features
- Up to about 3 years of coating durability
- Water contact angle of 107 degrees
- Chemical resistance pH 2–11
- 7H pencil hardness rating
- Wash marring resistance
- Strong gloss and surface slickness
- Resistant to salt, corrosion, UV and heat
- Nano-ceramic formulation
- V2: increased thickness, hardness and gloss depth over original
Usage
- Apply only to suitable surfaces: painted bodywork, motorbikes, hard plastic parts, headlights, taillights and alloy wheel rims.
- Avoid applying to aftermarket paint for 2–3 months as a precaution, and do not use on low-quality paint, glass, textiles, tyres or soft trims.
- Wear the included protective gloves and fit a fresh suede cloth to the supplied applicator block.
- Apply Cerberus V2 to the suede and work it into the surface using straight, overlapping passes, one panel at a time.
- Allow the coating to flash off, then buff away any residue with a clean microfibre cloth until the surface feels completely smooth.
핵심 특징
- 최대 약 3년 지속 내구성
- 물 접촉각 107도
- pH 2~11 화학 저항성
- 7H 경도
- 워시 마링 저항성
- 강한 광택과 슬릭한 표면감
- 염분·부식·UV·열 저항성
- 나노 세라믹 포뮬러
- V2: 이전 버전 대비 두께·경도·광택 깊이 향상
사용법
- 도장 바디워크, 모터사이클, 경질 플라스틱, 헤드라이트, 테일라이트, 알로이 휠 림 등 적합한 표면에만 도포합니다.
- 예방 차원에서 애프터마켓 도장 시공 후 2~3개월간은 사용을 삼가고, 저품질 도장·유리·직물·타이어·소프트 트림에는 사용하지 않습니다.
- 동봉된 보호 장갑을 착용하고, 어플리케이터 블록에 새 스웨이드 클로스를 장착합니다.
- 스웨이드에 케르베로스 V2를 취하고 패널별로 직선의 겹치기 방식으로 도포합니다.
- 코팅이 플래시될 때까지 기다린 뒤, 깨끗한 마이크로파이버 클로스로 잔여물을 닦아 표면을 매끄럽게 마무리합니다.