REBOOT NEXT
리부트 넥스트
REBOOT NEXT is a safer-formula silica scale remover made exclusively from organic acids, offering significantly lower health and paint-surface risks than conventional acid removers. It works in three modes — dry, wet, and shampoo-wash — and can also remove water spots from glass surfaces, making it a multifunctional eco-friendly cleaner with 96% biodegradability.
REBOOT NEXT는 유기산만으로 구성된 저자극 실리카 스케일 제거제로, 기존 산성 케미컬 대비 인체 및 도장면에 대한 위험성을 크게 낮췄습니다. 건식·습식·샴푸 세차의 3가지 방식으로 사용할 수 있으며 유리면의 물때 제거도 가능한 생분해성 96%의 친환경 다기능 클리너입니다.
- Brand
- Ganbass
- Categories
- Exterior : Remover
- Primary dilution
- RTU ~ 1:2
- pH
- acid
Key features
- Organic-acid-only formula — no inorganic acids
- Three application modes: dry, wet, and shampoo wash
- Removes silica scale from both painted and glass surfaces
- 96% biodegradable — environmentally friendly
- Slow-drying formula allows adjustable dwell time
- Low risk of acid staining on paint or coatings
- Dilutable up to 1:2 with purified water
Dilution
- Exterior : Remover — RTU ~ 1:2 (1:0-2) (primary)
Usage
- Wash the vehicle first to remove sand and dirt that could cause scratches.
- For dry application (standard): apply the liquid to a cloth and spread it over the scaled area, working in sections no larger than roughly 50 cm at a time.
- Allow dwell time as needed — wipe off immediately for gentle action, or leave up to 1 minute for heavy scale, then rinse or wipe away.
- For wet application: dampen and wring a microfiber cloth, apply the liquid to it, and work over the painted surface in a wash motion.
- Rinse the surface thoroughly with water, using a cloth to ensure all residue is removed.
- Check whether scale has been fully removed; repeat as necessary, extending dwell time if needed.
핵심 특징
- 유기산만 사용 — 무기산 미함유
- 건식·습식·샴푸 세차 3가지 시공 방식
- 도장면 및 유리면 실리카 스케일 동시 제거
- 생분해성 96% — 친환경 설계
- 느린 건조 특성으로 반응 시간 조절 가능
- 도장 및 코팅 피막에 대한 산 손상 위험 낮음
- 정제수로 최대 2배 희석 가능
사용법
- 먼저 세차를 실시하여 스크래치 원인이 되는 모래 먼지를 제거하십시오.
- 건식 시공(기본): 클로스에 본액을 적셔 스케일 부위에 도포하되, 한 번에 약 50cm 정도의 면적씩 나누어 작업하십시오.
- 목적에 따라 방치 시간을 조절하십시오 — 즉시 닦아내면 약하게, 최대 1분 방치하면 강하게 작용합니다. 이후 물로 씻어내거나 닦아내십시오.
- 습식 시공: 마이크로파이버 클로스를 적셔 꽉 짠 후 본액을 적셔 세차하는 요령으로 도장면에 도포하십시오.
- 클로스를 함께 사용하며 물로 충분히 헹궈 잔여물을 완전히 제거하십시오.
- 스케일이 완전히 제거되었는지 확인하고, 필요한 경우 방치 시간을 늘려 작업을 반복하십시오.
Also known as: 간바스, ganbas, Ganbass REBOOT NEXT, 간바스 리부트 넥스트, REBOOT-NEXT, Ganbass REBOOT-NEXT