FlexiCoat
플렉시코트
이우카 · EWO · 이우 · Ewocar FlexiCoat · FC · Ewocar FC · 이워카 플렉시코트
FlexiCoat is a professional-grade ceramic coating formulated for exterior and interior plastics, trim, bumpers, rubber seals, and textured surfaces. It penetrates and forms a dense, flexible membrane that restores original color depth and creates a slick, super-repellent surface resistant to dirt, water spots, and road contaminants. It also blocks UV radiation to prevent fading, chalking, and cracking, and withstands a pH range of 2–13.
플렉시코트는 외장 및 내장 플라스틱, 트림, 범퍼, 고무 씰, 텍스처 표면을 위한 전문가급 세라믹 코팅입니다. 표면에 침투해 밀도 높고 유연한 보호막을 형성하여 원래의 색상 깊이를 되살리고, 오염물과 물자국이 달라붙지 않는 발수 표면을 만들어줍니다. UV 차단 기능으로 변색과 갈라짐도 방지합니다.
- Brand
- EWOCAR
- Categories
- Interior : Trim Sealants
Key features
- Deep color restoration without greasy shine
- Super-repellent surface prevents dirt and water spot adhesion
- UV and oxidation protection against fading and cracking
- Multi-layer compatible for enhanced durability
- Chemical resistance pH 2–13
Usage
- Clean and degrease the plastic or rubber surface thoroughly using Ewocar Degreaser; ensure it is free of old dressings, silicones, and protectants.
- Apply FlexiCoat using a finger applicator or application sponge, working in small, controlled sections for uniform coverage.
- Allow the coating to bond for 1–2 minutes, then remove excess and level with a microfiber towel until the surface is even and streak-free.
- For a second layer, wait 1–2 hours before repeating steps 2–3.
- Keep the surface away from water for at least 18–24 hours; full curing and maximum performance develop over 9–10 days.
- For maximum film thickness (3–5 μm), the coating may alternatively be applied as a fine mist and left to dry naturally without wiping.
핵심 특징
- 번들거림 없이 색상 깊이를 깊게 복원
- 오염물과 물자국이 달라붙지 않는 초발수 표면
- 변색·갈라짐 방지를 위한 UV 및 산화 차단
- 다중 코팅으로 내구성 강화 가능
- pH 2~13 내화학성
사용법
- 이워카 디그리서로 플라스틱 또는 고무 표면을 완전히 세척·탈지하고, 기존 드레싱, 실리콘, 보호제 잔여물이 없는지 확인합니다.
- 핑거 어플리케이터 또는 어플리케이션 스펀지로 작은 구역씩 나누어 균일하게 코팅을 도포합니다.
- 1~2분간 결합시킨 후 마이크로파이버 타올로 잔여물을 제거하고 표면이 균일하고 얼룩 없이 될 때까지 닦아냅니다.
- 2차 도포 시 1~2시간 대기 후 2~3단계를 반복합니다.
- 최소 18~24시간 물 접촉을 피하고, 9~10일에 걸쳐 완전히 경화되어 최고 성능에 도달합니다.
- 최대 도막 두께(3~5 μm)를 원할 경우, 미세 분무 후 닦지 않고 자연 건조시키는 방법도 가능합니다.