그래핀 매트릭스 코팅 V2.0
Graphene Matrix Coating V2.0
에토스 · 이토스 · ethos · Ethos Graphene Matrix Coating V2.0 · 에토스 그래핀 매트릭스 코팅 V2.0
환원 그래핀 산화물(rGO) 레진과 추가 실리케이트, 저VOC 솔벤트를 적용해 도포가 한층 쉬워진 반영구 DIY 세라믹 코팅입니다. 물·먼지·오염물을 강하게 밀어내는 발수층을 만들어 스크래치, 워터스팟, 에칭 저항성을 높이고 광택도 끌어올려 줍니다. 브랜드 기준 약 5년 이상 지속될 수 있으며 도장면, 플라스틱 트림, 유리 전반에 사용 가능합니다.
- 브랜드
- Ethos Car Care
- 카테고리
- Exterior : Coating
- 기본 희석 비율
- RTU
핵심 특징
- 환원 그래핀 산화물(rGO) 레진
- 브랜드 기준 약 5년 이상 내구성
- 발수·오염 차단 나노 코팅
- 워터스팟·에칭·산화 저항
- 40% 레진 고형분 함량
- 도포가 쉬운 저VOC 솔벤트
- 도장면·플라스틱·유리에 사용
희석 비율
- Exterior : Coating — RTU (1:0) (기본)
사용법
- 차량을 세차한 뒤 클레이 바로 박힌 오염물을 제거하고, 봉인되기 전에 폴리싱으로 결함을 정리합니다.
- 에토스 디톡스로 폴리시 오일과 잔여물을 닦아내고 패널 틈에 남은 물기까지 모두 제거합니다.
- 병을 잘 흔든 뒤 어플리케이터에 코팅제를 몇 방울 떨궈 고르게 적십니다.
- 수평 패널부터 약 90cm × 90cm 구획으로 살짝 겹치는 직선으로 도포합니다.
- 도포 후 약 1~3분 두어 레인보우가 흐릿한 안개로 변하면 닦아낼 준비가 된 것입니다.
- 부드러운 마이크로파이버로 작은 원을 그리며 가볍게 닦아 잔여물을 완전히 제거합니다.
- 손전등으로 옆 패널의 밀린 잔여물을 확인한 뒤 다음 구역으로 이동해 차량 전체에 반복합니다.
- 추가 도포는 최소 1시간 간격을 두고, 코팅 경화를 위해 최소 48시간은 물에 닿지 않게 합니다.
Semi-permanent DIY ceramic coating reformulated with reduced graphene oxide (rGO) resins, added silicates, and a low-VOC solvent so it goes on more smoothly. It builds a hydrophobic layer that resists scratches and stains, repels water and dirt, and boosts gloss. The brand rates it for roughly 5 years or more, and it can be applied to paint, plastic trim, and glass.
Key features
- Reduced graphene oxide (rGO) resin
- About 5 years or more per brand
- Hydrophobic, dirt-shedding nanocoating
- Resists water spots, etching, oxidation
- 40% resin solids content
- Low-VOC solvent for smoother application
- Use on paint, plastic, or glass
Usage
- Wash the car, then clay bar embedded contaminants and polish out defects before they get sealed in.
- Wipe down with Ethos Detox to clear polish oils and residues, and dry any water trapped in panel gaps.
- Shake the bottle and put a few drops onto the applicator until it is evenly saturated.
- Working 3 ft by 3 ft sections starting on horizontal panels, lay slightly overlapping straight lines.
- Wait about 1 to 3 minutes until the rainbow look turns to a haze, ready for removal.
- Buff the section with a soft microfiber in small circles with light pressure to clear all residue.
- Check adjacent panels with a flashlight for pushed residue, then continue across the vehicle.
- Wait at least one hour between coats and keep the surface dry for at least 48 hours to cure.