DIY Detail 1 Year Graphene Ceramic Coating
DIY 디테일 1년 그래핀 세라믹 코팅
A TEOS-based graphene ceramic coating that lays down easily and adds gloss, slickness, and around a year of protection. The TEOS chemistry helps the product resist clogging during application and hold up against fracturing on the surface. It is intended for paint, PPF and vinyl, glass, trim, chrome, and wheels.
TEOS를 베이스로 한 그래핀 세라믹 코팅으로 시공이 쉽고 광택과 매끈함을 더하면서 약 1년 정도의 보호를 제공합니다. TEOS 포뮬러 덕분에 시공 중 막힘이 적고 표면에서 균열에도 비교적 강합니다. 도장면, PPF 및 비닐, 유리, 트림과 크롬, 휠 등 다양한 외장 부위에 사용할 수 있습니다.
- Brand
- DIY Detail
- Categories
- Exterior : Coating
Key features
- About 1 year of graphene ceramic protection
- TEOS-based formula resistant to clogging
- Adds visible gloss and slickness
- Multiple application methods supported
- Compatible with PPF and vinyl wraps
- Safe on paint, PPF, vinyl, glass, trim, chrome, and wheels
Usage
- Begin on a clean, dry, fully decontaminated surface.
- Confirm the surface is above about 40 F (5 C) and will stay there for at least an hour.
- Prep the panel with DIY Detail Panel Prep or C6 Ceramics APP.
- Spray and towel method: mist a Level 1 short-nap towel and spread, using 3 to 4 sprays per additional panel.
- Spray and applicator method: mist a foam coating applicator and spread evenly, with 3 to 4 sprays per panel.
- Dropper method: place 8 to 10 drops on the applicator for the first panel and about 2 to 3 drops on each later panel.
- Let the coating flash, then level with a Freebird 400 towel.
- Drive the car after about 1 hour, wait about 3 days before washing with Rinse Less Wash, and allow about 7 days for full cure.
- After application, spray any leftover product back into the bottle and clean the sprayer with Rinse Less Wash or Panel Prep.
핵심 특징
- 약 1년의 그래핀 세라믹 보호
- 막힘에 강한 TEOS 기반 포뮬러
- 눈에 띄는 광택과 매끈함
- 다양한 시공 방식 지원
- PPF·비닐 랩 호환
- 도장·PPF·비닐·유리·트림·크롬·휠에 안전
사용법
- 깨끗하고 건조하며 디컨타미네이션이 끝난 도장면에서 시작합니다.
- 표면 온도가 약 40 F(5 C) 이상이고 최소 1시간 이상 유지되는지 확인합니다.
- DIY Detail 패널 프렙이나 C6 세라믹스 APP로 패널을 준비합니다.
- 스프레이/타월 방식: 레벨 1 단모 타월에 분사해 펴 바르고 추가 패널마다 3~4회씩 분사합니다.
- 스프레이/어플리케이터 방식: 폼 코팅 어플리케이터에 분사해 고르게 펴 바르고 추가 패널마다 3~4회 분사합니다.
- 드로퍼 방식: 첫 패널에는 8~10방울, 이후 패널에는 약 2~3방울을 어플리케이터에 떨어뜨립니다.
- 코팅이 자연스럽게 플래시되도록 둔 다음 Freebird 400 타월로 레벨링합니다.
- 약 1시간 후 주행 가능, 약 3일 후 Rinse Less Wash로 세차, 약 7일 후 완전 경화됩니다.
- 시공이 끝나면 남은 코팅을 보틀로 다시 분사하고 Rinse Less Wash나 패널 프렙으로 분사기를 세척합니다.