Pro Slip
프로 슬립
An advanced slip solution formulated for professional installation of PPF, colour change films, and window tints, providing ideal slipperiness for precise film positioning without damaging the adhesive. The formula reduces adhesive pulling and film lines, maintains long-lasting slip on unfinished surfaces, and accelerates drying time after installation.
PPF, 컬러 체인지 필름 및 윈도우 틴트의 전문 시공을 위해 설계된 고급 슬립 용액으로, 접착제를 손상시키지 않고 필름을 정밀하게 위치 조정할 수 있는 이상적인 미끄러짐을 제공합니다. 접착제 당김과 필름 라인 형성을 억제하고, 미완성 표면에서도 지속적인 슬립성을 유지하며, 시공 후 건조 시간을 단축합니다.
- Brand
- ADBL
- Categories
- Exterior : PPF Maintenance
- Primary dilution
- 1:50~1:500
Key features
- Dilution range 1:50~1:500 depending on application
- Does not damage adhesive or leave residue
- Easily removable with cold water
- Reduces adhesive pull and film lines
- Long-lasting slip on incomplete surfaces
- Accelerates drying under the film
Dilution
- Exterior : PPF Maintenance — 1:50~1:500 (1:50-500) (primary)
Usage
- Mix the appropriate amount of Pro Slip with demineralised water (optimum 5 ml per 1 L; for high-tension elements requiring longer working time, use 10–15 ml per 1 L).
- Apply the solution to both the topcoat side and the liner side of the film to remove impurities and neutralize electrostatic charge, then remove with a silicone squeegee.
- Apply the solution to the car surface to be covered, then squeegee off to remove dust and loose dirt; repeat if necessary.
- When removing the liner, apply the solution directly onto the adhesive and onto the car surface just before installing the film; place the film and squeegee out the solution. To close film edges, rinse remaining slip solution using demineralised water with or without 20% IPA.
핵심 특징
- 용도에 따라 1:50~1:500 희석 범위
- 접착제 손상 없음, 잔여물 없음
- 냉수로 쉽게 제거 가능
- 접착제 당김 및 필름 선 형성 억제
- 미완성 표면에서 지속적인 슬립성 유지
- 필름 하단 건조 시간 단축
사용법
- 적절한 양의 프로 슬립을 탈이온수에 희석합니다 (기본 1L당 5ml; 높은 인장력이 필요하거나 긴 작업 시간이 필요한 부위는 1L당 10~15ml 사용).
- 필름의 표면 코팅 면과 라이너 면에 용액을 도포하여 이물질 제거 및 정전기를 중화한 후 실리콘 스퀴지로 제거합니다.
- 필름을 씌울 차량 표면에 용액을 도포하고 스퀴지로 제거하여 먼지와 느슨한 오염물질을 제거합니다; 필요시 반복합니다.
- 라이너를 제거할 때 접착면과 차량 표면에 바로 용액을 도포한 후 필름을 올리고 스퀴지로 밀어냅니다. 필름 가장자리를 마무리할 때는 IPA 20% 혼합 또는 순수 탈이온수로 잔여 슬립 용액을 씻어냅니다.