Graphene Ceramic Spray Coating Advanced
그래핀 세라믹 스프레이 코팅 어드밴스드
Graphene Ceramic Spray Coating Advanced doubles the graphene resin content compared to the standard version, delivering about 12-18 additional months of ceramic protection in a fast spray-and-wipe format. UV Tracer Technology confirms full coverage so spots are not missed, and the updated formula achieves a notably low sliding angle for strong water evacuation. It sits at the top of the Adam’s graphene spray coating lineup.
Graphene Ceramic Spray Coating Advanced는 기존 스프레이 코팅 대비 그래핀 수지 함량을 2배로 높여 약 12~18개월의 세라믹 보호 효과를 빠른 스프레이 시공으로 제공합니다. UV 추적 기술로 도포 누락 부위를 방지하고, 개선된 포뮬러로 물이 낮은 각도에서도 빠르게 흘러내리는 강한 발수 성능을 발휘합니다.
- Brand
- Adam's Polishes
- Categories
- Exterior : Coating
Key features
- Less prone to water spotting
- Water evacuation at angles below about 10-15 degrees
- About 100% more graphene resin than the standard version
- UV tracer for coverage verification
- About 12-18 months of spray ceramic protection
Usage
- Prepare the vehicle with a clay bar or mitt and a swirl killer to fully decontaminate and correct the surface before coating.
- Apply Surface Prep to all panels using a microfiber towel to degrease and improve coating adhesion.
- Shake thoroughly, then spray the coating onto one panel at a time from about one foot away.
- Work the product evenly across the surface with a clean microfiber towel in overlapping straight passes.
- Allow to flash briefly until the coating begins to haze, then buff off cleanly with a second fresh microfiber towel.
- Use a UV light to confirm complete and even coverage across the entire panel before moving on.
- Cure the finished vehicle for the full recommended period, keeping it dry and away from water or contamination.
핵심 특징
- 워터 스팟 발생 감소
- 약 10~15도 이하 각도에서도 빠른 물 흘러내림
- 기존 대비 그래핀 수지 약 100% 증가
- UV 추적으로 도포 상태 확인
- 약 12~18개월의 스프레이 세라믹 보호
사용법
- 클레이 바 또는 미트와 광택기를 사용해 표면을 완전히 오염 제거하고 결함을 수정합니다.
- 극세사 타월에 서피스 프렙을 묻혀 모든 패널을 탈지하여 코팅 밀착력을 높입니다.
- 충분히 흔든 후 약 30cm 거리에서 한 패널씩 코팅제를 분사합니다.
- 깨끗한 극세사 타월로 직선 방향으로 겹치며 고르게 펴 바릅니다.
- 코팅이 뿌옇게 변하면 새 극세사 타월로 잔여물을 깨끗이 버핑합니다.
- UV 라이트로 패널 전체에 균일하게 도포되었는지 확인하고 다음 패널로 이동합니다.
- 권장 경화 기간 전체 동안 차량을 건조하게 유지하고 물이나 오염에 노출시키지 않습니다.