Trim+ Coating - Trim Restore
트림 플러스 코팅 - 트림 리스토어
Trim+ is a black dye-infused trim coating built to restore, refresh, and protect exterior plastic and rubber trim in a single application. The deep-black dye chemistry penetrates faded, oxidized, and weathered trim, returning it to a rich finish while locking the color in. The coating also adds a hydrophobic shield and strong UV resistance, holding deep black for up to about 2 years without streaking or washing off.
Trim+는 외장 플라스틱·고무 트림을 한 번의 도포로 복원·회복·보호하도록 만든 블랙 다이 인퓨즈드 트림 코팅입니다. 딥 블랙 다이 화학이 퇴색·산화·풍화된 트림에 침투해 풍부한 마감을 되살리고 색을 고정시킵니다. 발수 보호막과 강한 UV 저항도 함께 더해 줄무늬나 씻겨남 없이 약 2년간 진한 블랙을 유지합니다.
- Brand
- Armour Detail Supply
- Categories
- Exterior : Coating
Key features
- Black dye-infused trim coating
- Restores faded and oxidized trim
- Deep-black dye chemistry
- Hydrophobic shield
- Strong UV resistance
- Up to about 2 years of durability
- Safe on plastics, rubber, bumpers, moldings
- Permanent dye-infused bond
Usage
- Wash the trim surface with Armour Decon Soap.
- For older or oxidized trim, scrub it with Armour Tire Cleaner diluted 4:1 as an optional prep step.
- Wipe with Armour Panel Prep to clear oils and residue, repeating twice for a clean surface.
- Prime the applicator with three lines of coating to start; later sections only need a small amount.
- Apply Trim+ to one section at a time using firm circular motions to work the product into the plastic, then let it set up 1-2 minutes.
- Level with a fresh towel using small circular motions, checking for streaks or dark high spots and repeating per section.
- Trim+ is built as a single layer but can be layered for heavily neglected trim, with a few minutes between coats.
- Allow 4 hours of initial cure before water exposure, and avoid washes or chemicals for 24 hours.
핵심 특징
- 블랙 다이 인퓨즈드 트림 코팅
- 퇴색·산화 트림 복원
- 딥 블랙 다이 화학
- 발수 보호막
- 강한 UV 저항
- 약 2년 내구성
- 플라스틱·고무·범퍼·몰딩에 안전
- 영구적인 다이 본딩
사용법
- Armour 디콘 솝으로 트림 표면을 세척합니다.
- 오래되거나 산화된 트림은 Armour 타이어 클리너를 4:1로 희석해 문지르는 선택 단계를 진행합니다.
- Armour 패널 프렙으로 오일·잔여물을 제거하며 깨끗한 표면을 위해 두 번 반복합니다.
- 어플리케이터를 3줄 도포로 프라이밍하고 이후 섹션에는 소량만 추가합니다.
- Trim+를 한 섹션씩 단단한 원형 모션으로 플라스틱에 스며들게 도포한 뒤 1-2분 셋업합니다.
- 새 타월로 작은 원을 그리며 레벨링하고 줄무늬나 어두운 하이스팟을 확인하며 섹션마다 반복합니다.
- Trim+는 단일 레이어 코팅이지만 심하게 방치된 트림은 다층 도포가 가능하며 레이어 사이에는 수 분 간격을 둡니다.
- 4시간 초기 경화 후 물에 노출하고, 24시간 동안은 세차나 케미컬 노출을 피합니다.