servFaces 플라스틱 코트 희석비 & 사용 가이드

servFaces 플라스틱 코트 희석비 pH 스펙 카드

Plastic Coat

미처리 플라스틱 표면을 위한 투명 고강도 코팅으로 실키한 광택과 지속적인 보호를 남깁니다. 투명한 피막은 오염에 강하고 약 680°C까지 내화 특성을 유지하며 일반 세정제로는 벗겨지지 않습니다. UV 차단 성분이 들어 있어 미처리 플라스틱을 시간이 지나도 변색으로부터 보호합니다.

브랜드
servFaces
카테고리
Exterior : Coating, Interior : Trim Sealants
기본 희석 비율
RTU
최종 업데이트
2026-06-02

핵심 특징

희석 비율

용도희석비율
Exterior : Coating (기본)RTU1:0

사용법

  1. 서피스 클리너 울티마로 표면을 닦은 뒤 서피스 클리너 뉴트라로 중화합니다.
  2. 어플리케이터에 도포 클로스를 끼웁니다.
  3. 플라스틱 코트를 12~18방울 클로스에 떨어뜨리고 최대 50x50cm 구역씩 빠르게 펴 발라 눈에 보이는 피막을 만듭니다.
  4. 도포량, 습도, 온도에 따라 약 1~3분간 반응시킵니다.
  5. 스페셜 코팅 타월로 가장자리부터 안쪽으로 직선의 빠른 동작으로 잉여 제품을 닦아냅니다.
  6. 새 스페셜 코팅 타월로 약한 압력을 주며 가장자리부터 안쪽으로 원을 그리며 닦습니다.
  7. 얼룩이 남으면 새 스페셜 코팅 타월로 표면이 깨끗해질 때까지 반복합니다.
  8. 재코팅은 20분 후 가능하며 35분 이내에 해야 합니다.

A transparent, high-strength coating made for untreated plastic surfaces, leaving a silky gloss with lasting protection. The clear film resists dirt, holds up to temperatures around 680°C without losing its fireproof properties, and cannot be taken off with ordinary cleaners. A built-in UV blocker helps protect untreated plastics from discoloration over time.

Key features

  • High-strength transparent coating for untreated plastics
  • Leaves a silky gloss
  • Resists dirt and easy to clean
  • Heat-resistant to around 680°C without affecting fireproof properties
  • Not removable with ordinary cleaners
  • Built-in UV blocker against long-term discoloration
  • Flexible film up to 5 µm that does not chip or peel
  • Can be applied by compressed-air spraying

Usage

  1. Clean the surface with Surface Cleaner Ultima, then neutralize with Surface Cleaner Neutra.
  2. Fit the application cloth onto the applicator.
  3. Put 12 to 18 drops of Plastic Coat on the cloth and spread it quickly in sections of up to 50 x 50 cm to form a visible film.
  4. Let it react for about 1 to 3 minutes depending on amount applied, humidity, and temperature.
  5. Remove the excess with a Special Coating Towel, starting at the edges and working inward with straight, quick strokes.
  6. Polish with a fresh Special Coating Towel under light pressure, moving from the edges inward in circles.
  7. If streaks remain, repeat the polishing step with another fresh Special Coating Towel until the surface is clear.
  8. Recoating is possible after 20 minutes but should be done within 35 minutes.

다른 이름: serv, 서브페이스, 서브, servFaces Plastic Coat, SF Plastic Coat, PC, servFaces PC, SF PC, 서브페이시스 플라스틱 코트, 서브페이시스 PC, SF10009.1

View in English

출처

관련 제품

servFaces의 다른 제품

같은 카테고리(Coating) 제품

더 보기