W28 울트라 컴파운드
W28 Ultra Compound
Nihachi Pro · 니하치 · 니하치프로 · nihachi · W28 Ultra Compound 100ml · Nihachi Pro W28 Ultra Compound 100ml · 28pro W28 Ultra Compound 100ml · W28 Ultra · W28 울트라 컴파운드 100ml · 니하치 프로 W28 울트라 컴파운드 100ml · W28 Ultra Compound 500ml · Nihachi Pro W28 Ultra Compound 500ml · 28pro W28 Ultra Compound 500ml · W28 울트라 컴파운드 500ml · 니하치 프로 W28 울트라 컴파운드 500ml
하나의 제품으로 초벌 연마부터 진한 색상 차량의 최종 마무리까지 커버하는 차세대 극초미립자 컴파운드입니다. 버프 종류를 교체하는 것으로 연마력을 조절하며, 코팅 밀착을 방해하지 않습니다. 단, 코팅 전 탈지 세척은 권장됩니다.
- 브랜드
- 니하치 프로
- 카테고리
- Exterior : Polishes
핵심 특징
- 초벌 연마부터 최종 마무리까지 단일 제품으로 해결
- 10단계 기준 4~10의 극초미립자 연마 레벨
- 버프 종류 교체(울 버프, 우레탄 버프)로 연마력 조절
- 코팅 밀착력을 방해하지 않음
- 코팅 전 탈지 세척 권장
사용법
- 세차를 실시하여 차체의 오염을 충분히 제거합니다.
- 철분, 물자국 등 고착 오염물을 제거합니다.
- 고무, 라이트 등 컴파운드가 닿으면 안 되는 부위에 마스킹 테이프를 붙입니다.
- 컴파운드를 잘 흔든 후, 더블 액션 또는 기어 액션 폴리셔의 버프에 소량(팥알 크기 2~3개 분량)을 묻혀 약 50cm×50cm 범위를 도장면이 보일 때까지 연마합니다.
- 탈지 샴푸로 패널 틈새 컴파운드 잔분을 세척합니다.
- 필요한 경우 코팅 작업으로 진행합니다.
A next-generation ultra-fine polishing compound that handles everything from initial cutting to final finishing on dark-colored vehicles, all in a single product. Polishing intensity is controlled by switching buff types rather than changing compounds. It does not inhibit coating adhesion, though a degreasing wash is still recommended before coating.
Key features
- One product covers full range from initial cut to final finish
- Ultra-fine abrasive level rating 4 to 10 on a 10-point scale
- Polishing power controlled via buff selection (wool, urethane pads)
- Does not inhibit coating adhesion
- Degreasing wash recommended before coating application
Usage
- Wash the vehicle thoroughly to remove surface dirt.
- Remove iron particles, water spots, and other bonded deposits.
- Mask off rubber trims, lights, and any areas that should not be polished.
- Shake the compound well. Apply a small amount (2-3 azuki-bean-sized drops) to the buff on a dual-action or gear-action polisher, and work a roughly 50 cm × 50 cm section at a time until the paint surface becomes visible.
- Degrease with a degreasing shampoo to remove polish residue from panel gaps.
- Proceed to coating application if desired.