도미넥스
DOMINEX
DOMINEX는 완전 무용제 수성 나노 세라믹 경화 코팅제로, 도장 표면의 미세 핀홀 내부에 얇은 자립 골격막을 형성하여 두꺼운 희생 피막 없이 도장 밀도를 내부에서부터 강화합니다. 기존의 두꺼운 경화 코팅과 달리 고밀도 나노 세라믹 충전을 통한 지반 강화를 목표로 하며, 도장의 질감과 강도를 높여줍니다.
- 브랜드
- Ganbass
- 카테고리
- Exterior : Coating
- 기본 희석 비율
- RTU
핵심 특징
- 완전 무용제 수성 배합
- 초박막 자립 나노 골격막 형성
- 습식 시공으로 섬세한 도장 면에서의 시공 리스크 최소화
- 두꺼운 희생 피막 없이 도장 밀도 향상
- 희생 피막 없는 초박막 코팅 철학
- 도장 인성 및 균열 저항성 향상
- MODEL247과 조합하여 완성형 초박막 보호 시스템 구현
희석 비율
- Exterior : Coating — RTU (1:0) (기본)
사용법
- 세차 후 적절한 하지 처리를 합니다. 본 제품은 습식 시공 전용이므로 도장면이 약간 젖어 있어도 괜찮습니다.
- 물기를 짜낸 UltraWick Cloth에 적당량의 액제를 적시고, 도장면에 마사지하듯 여러 번 부드럽게 도포합니다.
- 젖은 상태로 단단히 짠 UltraWick Cloth로 잉여분을 닦아낸 후, 마른 천으로 마무리 닦음합니다.
- 시공 후 가능하면 약 3시간 동안 도장면을 만지거나 물에 닿지 않도록 합니다.
- 오버코트를 원한다면 DOMINEX 시공 2~3시간 후 MODEL247 또는 SILENTFORCE를 시공합니다.
DOMINEX is a completely solvent-free, water-based nano-ceramic hardening coating designed to form an ultra-thin self-supporting skeletal film within the micro-pinholes of paint surfaces, thereby strengthening the paint's density from within rather than building a thick sacrificial layer on top. Unlike conventional thick-film hardening coatings, it targets ground-level reinforcement through high-density nano-ceramic infill, improving paint toughness and resistance without added bulk.
Key features
- Completely solvent-free, water-based formulation
- Ultra-thin self-supporting nano-skeleton film
- Wet application method reduces application risk on delicate paint
- Increases paint density without thick sacrificial film
- No-sacrifice-layer (thin-film) coating philosophy
- Improves paint toughness and crack resistance
- Pairs with MODEL247 for a complete thin-film protection system
Usage
- After washing the vehicle, perform appropriate surface preparation; the paint surface may be slightly damp, as this product is designed for wet application.
- Apply a small amount of the liquid to a damp-wrung UltraWick Cloth and gently work it into the paint surface using a massaging motion over multiple passes.
- Wipe away any excess with a damp, firmly wrung UltraWick Cloth, then finish with a dry wipe.
- After application, avoid touching or wetting the surface for approximately three hours if possible.
- If an overcoat is desired, apply MODEL247 or SILENTFORCE two to three hours after DOMINEX application.
다른 이름: 간바스, ganbas, Ganbass DOMINEX, 간바스 도미넥스