Rubber & Plastic Parts Restoration Agent
러버 앤 플라스틱 파츠 레스토레이션 에이전트
소프트99 · soft · 소프트 · Soft99 Rubber & Plastic Parts Restoration Agent · 소프트99 러버 앤 플라스틱 파츠 레스토레이션 에이전트
A silicone compound coating kit that restores the deep darkness, natural gloss, and rich texture of faded exterior unpainted plastic and rubber trim. The coating liquid penetrates the surface and polymerizes to form a flexible, glossy film suitable for both hard plastic and soft rubber parts.
퇴색된 외장 무도장 플라스틱 및 고무 트림의 깊은 블랙과 자연스러운 광택을 복원하는 실리콘 계열 코팅 키트입니다. 코팅액이 표면에 침투·폴리머화하여 하드 플라스틱과 소프트 고무 모두에 적합한 유연하고 광택 있는 피막을 형성합니다.
- Brand
- Soft99
- Categories
- Interior : Trim Sealants
Key features
- Silicon compound coating restores faded plastic and rubber trim
- Penetrates surface and polymerizes for durable flexible film
- Suitable for both hard plastic and soft rubber parts
- Includes silicone-off degreasing wipes, hard and soft sponges, and gloves
- Do not use on driving-related parts such as steering wheel, pedals, wipers, or tires
Usage
- Clean and degrease the area using the included silicone-off wipes; remove any fibres from textured plastics before proceeding. Seal the wipe package firmly between uses.
- Cut the sponge to match the area: use the black (hard) sponge for hard plastic, and the white (soft) sponge for rubber. Apply a small amount of the coating liquid and spread thinly and evenly; continue applying to rubber parts until the surface is saturated.
- Allow to dry for approximately 5 minutes, then lightly wipe with a fresh sheet for an even finish. Do not leave excess on the surface as it cannot be removed once fully cured.
- Do not touch or wet the treated surface for 24 hours after application.
핵심 특징
- 실리콘 컴파운드 코팅으로 퇴색된 플라스틱·고무 트림 복원
- 표면 침투 후 폴리머화하여 내구성 있는 유연한 피막 형성
- 하드 플라스틱과 소프트 고무 모두 사용 가능
- 실리콘 오프 탈지 시트, 하드·소프트 스펀지, 장갑 포함
- 스티어링 휠, 페달, 와이퍼, 타이어 등 주행 관련 부품에는 사용 금지
사용법
- 포함된 실리콘 오프 탈지 시트로 도포 부위를 세정·탈지하세요. 결이 있는 플라스틱에 시트 섬유가 남으면 진행 전 제거하고, 시트 패키지는 사용 후 단단히 밀봉하세요.
- 도포 면적에 맞게 스펀지를 잘라 사용하세요: 하드 플라스틱에는 검정(하드) 스펀지, 고무에는 흰색(소프트) 스펀지를 사용하세요. 소량의 코팅액을 묻혀 얇고 고르게 펴 바르고, 고무 부품은 충분히 흡수될 때까지 계속 도포하세요.
- 약 5분간 건조 후 새 시트로 가볍게 닦아 고른 마감을 만드세요. 완전히 경화되면 제거가 불가능하므로 잔여물을 오래 방치하지 마세요.
- 도포 후 24시간 동안 표면을 만지거나 수분에 노출시키지 마세요.