Synergy Lite
시너지 라이트
인피니티 · 인피니티 왁스 · infinity · Infinity Wax Synergy Lite · IW Synergy Lite · SL · 인피니티 왁스 시너지 라이트 · IFW106
Synergy Lite v2 is a 1-year sprayable ceramic coating based on Polysilazane resin combined with advanced solvents and a sacrificial top-layer polymer that enables outdoor application and protects the coating while it cures. A single 100 ml glass bottle covers up to 5 vehicles, bonds to paintwork, glass, and unpainted trim, and reaches 9H hardness after 7 days without washing.
시너지 라이트 v2는 폴리실라잔 수지를 기반으로 고급 용매와 희생층 폴리머가 결합된 1년 지속 스프레이형 세라믹 코팅입니다. 야외 시공을 가능하게 하고 경화 중 코팅을 보호하는 희생층 시스템 덕분에 DIY 사용자도 손쉽게 시공할 수 있습니다. 100 ml 유리병 하나로 최대 5대의 차량에 적용 가능하며, 7일 후 세차를 피하면 9H 경도에 도달합니다.
- Brand
- Infinity Wax
- Categories
- Exterior : Coating
- Primary dilution
- RTU
Key features
- 1-year ceramic protection from Polysilazane resin
- Sacrificial top layer enables outdoor application
- Rain-safe within 30 minutes of application
- Bonds to paint, glass, and unpainted plastic trim
- Fills minor swirls and wash marring without polishing
- 100 ml bottle covers up to 5 vehicles
Dilution
- Exterior : Coating — RTU (1:0) (primary)
Usage
- Thoroughly wash, decontaminate, and (if required) machine polish the vehicle before application.
- Apply Synergy Prep panel wipe one panel at a time to remove residual oils and contamination.
- Spray Synergy Lite 6–8 times onto a microfibre ceramic applicator block to prime it; never spray directly on the car.
- Apply the coating in straight lines across one panel at a time, cross-hatching for an even bond.
- Allow 30 seconds to 5 minutes (up to 15 minutes maximum) before removing residue with a short-pile microfibre towel.
- Once the entire vehicle is coated, give it a final wipe with a plush edgeless towel. Do not wash for 7 days after application.
핵심 특징
- 폴리실라잔 수지 기반 1년 세라믹 보호
- 희생층으로 야외 시공 가능
- 시공 후 30분 이내 빗물 접촉 가능
- 도장면, 유리, 미도장 플라스틱 트림에 결합
- 폴리싱 없이도 미세 스크래치 및 세차 흔적 개선
- 100 ml 한 병으로 최대 5대 시공 가능
사용법
- 시공 전 차량을 충분히 세차, 오염 제거하고 필요한 경우 기계 폴리싱을 진행합니다.
- 시너지 프렙 패널 와이프를 한 패널씩 사용하여 잔여 오일과 오염물을 제거합니다.
- 마이크로파이버 세라믹 어플리케이터 블록에 시너지 라이트를 6~8회 분사하여 패드를 적셔 줍니다. 차량에 직접 분사하지 마세요.
- 한 번에 한 패널씩 직선으로 코팅을 도포하고, 균일한 결합을 위해 가로세로 교차 도포합니다.
- 30초~5분(최대 15분) 후 단섬유 마이크로파이버 타월로 잔여물을 닦아 냅니다.
- 전체 차량 시공 완료 후 부드러운 에지리스 타월로 마무리 닦음을 합니다. 시공 후 7일간 세차하지 않습니다.