REBOOT-TYPE-NC
리부트 타입 NC
An acid-based silica scale remover formulated specifically for the delicate clear-coat surfaces of new and repainted vehicles. It uses plant-based acids such as plum vinegar to provide gentle but effective scale removal with lower risk of chemical damage than standard acidic removers, making it also suitable for hardened coatings with low acid resistance.
신차 도장과 재도장 차량의 민감한 클리어 도장면을 위해 설계된 산성 실리카 스케일 제거제입니다. 매실초 등 식물성 산을 배합하여 일반 산성 케미컬보다 낮은 위험도로 스케일을 효과적으로 제거하며, 산성 케미컬에 취약한 경화계 코팅 피막에도 사용할 수 있습니다.
- Brand
- Ganbass
- Categories
- Exterior : Remover
- Primary dilution
- RTU
- pH
- acid
Key features
- Plant-based organic acids (including plum vinegar) for gentle action
- Optimized for new and repainted paint surfaces
- Lower risk of chemical damage versus standard acidic removers
- Safe for hardened coatings with low acid resistance
- Usable as a diagnostic tool to assess paint condition
- Removes light silica scale and water-spot deposits
Dilution
- Exterior : Remover — RTU (1:0) (primary)
Usage
- Wash the vehicle and wipe off water droplets, leaving slight residual moisture acceptable.
- Put on rubber gloves, as this is an acid-based product.
- Apply an appropriate amount of the product to a round cloth or microfiber cloth without soaking through.
- Spread the product over the paint surface in a washing motion, working in approximately 50 cm square sections at a time.
- Immediately wipe off the excess with a dedicated wiping cloth or microfiber cloth — wet wipe followed by dry wipe is also acceptable.
- If not removed in one pass, repeat two or three times as needed.
- After completing the work, wash the vehicle with a degreasing shampoo, then proceed to coating application.
핵심 특징
- 매실초 등 식물성 유기산 배합으로 온화한 작용
- 신차 및 재도장 도장면에 최적화
- 일반 산성 제거제 대비 낮은 화학 손상 위험
- 산성 케미컬에 취약한 경화계 코팅에도 사용 가능
- 도장 상태 진단 도구로도 활용 가능
- 경미한 실리카 스케일 및 물자국 제거
사용법
- 세차 후 물방울을 닦아내세요. 약간의 수분 잔류는 문제없습니다.
- 산성 케미컬이므로 고무장갑을 착용하세요.
- 원형 클로스 또는 마이크로파이버 클로스에 액이 흘러내리지 않을 정도로 적당량을 묻히세요.
- 세차하는 요령으로 도장면에 제품을 펴 바르되, 한 번에 50cm 정방 정도의 범위씩 작업하세요.
- 펴 바른 후 즉시 전용 닦아내기 클로스 등으로 잉여분을 닦아내세요. 젖은 닦기 후 마른 닦기도 가능합니다.
- 한 번에 제거되지 않을 경우 2~3회 반복하세요.
- 작업 완료 후 탈지 샴푸 등으로 세차하고 코팅 작업을 진행하세요.
Also known as: 간바스, ganbas, Ganbass REBOOT-TYPE-NC, 간바스 리부트 타입 NC, REBOOT TYPE NC