REBOOT-GEL High Viscosity PLUS
리부트 젤 고점도 플러스
REBOOT-GEL High Viscosity PLUS is an upgraded version of the standard REBOOT GEL High Viscosity, offering enhanced silica scale removal performance for wet-application use. It is an acid-based gel (organic acid, inorganic acid, surfactant, hydrophilic agent) designed for DIY users who need stronger descaling power than the standard high-viscosity formula. Exclusively for wet-application, it must be used on a water-wetted paint surface to minimize application scratches.
REBOOT-GEL 고점도 플러스는 기존 REBOOT 젤 고점도의 업그레이드 버전으로, 실리카 스케일 제거율을 더욱 향상시킨 DIY용 산성 젤 타입 케미컬입니다. 유기산, 무기산, 계면활성제, 친수제로 구성된 산성 제품으로, 습식 시공 전용으로 설계되어 시공 흠집을 최소화하면서 스케일 제거가 가능합니다.
- Brand
- Ganbass
- Categories
- Exterior : Remover
- Primary dilution
- RTU
- pH
- acid
Key features
- Enhanced silica scale removal vs. standard high-viscosity formula
- Acid-based gel (organic acid, inorganic acid, surfactant)
- Wet-application only — used on water-covered paint surface
- Minimizes application scratches due to gel lubrication
- DIY-oriented formulation with lower risk profile
- Non-classified hazardous substance (毒劇物指定外)
Dilution
- Exterior : Remover — RTU (1:0) (primary)
Usage
- Put on rubber gloves before use, as this is an acid product.
- Perform a compatibility test on a small, inconspicuous area before full application.
- Cut the application cloth to a width matching your fingers for optimal control.
- Confirm the paint surface is wet from washing, then apply the gel by spreading it across the wetted surface.
- Before the product dries, rinse off thoroughly with water while wiping with a cloth, and check that the treated surface has turned hydrophilic.
- If applying a wet over-coat afterward, proceed immediately; if applying a dry or cured coating, wipe off all moisture and allow to dry completely first.
핵심 특징
- 기존 고점도 대비 실리카 스케일 제거율 향상
- 산성 젤 타입 (유기산, 무기산, 계면활성제)
- 습식 시공 전용 — 물기 있는 도막 위에서 사용
- 젤 윤활 효과로 시공 흠집 최소화
- DIY 사용자를 위한 저리스크 포뮬러
- 독·극물 지정 외 제품
사용법
- 산성 제품이므로 사용 전 고무 장갑을 착용합니다.
- 눈에 잘 띄지 않는 곳에서 궁합 테스트를 먼저 실시합니다.
- 도포에 사용할 클로스를 손가락 폭에 맞게 잘라 조작성을 높입니다.
- 세차 후 도막 표면에 물기가 있는 것을 확인한 뒤 젤을 도포하여 고르게 펴 바릅니다.
- 제품이 마르기 전에 물로 헹구면서 클로스로 성분을 닦아내고, 시공 부위가 친수성으로 변했는지 확인합니다.
- 습식 오버코팅을 이어서 시공할 경우 그대로 진행하고, 건식 또는 경화계 코팅을 사용할 경우 물기를 완전히 닦아낸 뒤 건조시킵니다.
Also known as: 간바스, ganbas, REBOOT-GEL-高粘度-PLUS, Ganbass REBOOT-GEL-高粘度-PLUS, 간바스 리부트 젤 고점도 플러스, REBOOT GEL High Viscosity PLUS, REBOOT GEL 高粘度 PLUS, REBOOT-GEL Konetsu PLUS, Ganbass REBOOT-GEL Konetsu PLUS, REBOOT-GEL 高粘度 PLUS