Fine Cut
파인 컷
이우카 · EWO · 이우 · Ewocar Fine Cut · FC · 이워카 파인 컷
Fine Cut is a finishing polishing compound formulated to refine the paint surface after aggressive correction stages. It removes holograms, micro-marring, and light scratches while delivering a 10/10 gloss rating with an extremely clear, deep mirror-like finish. Best paired with the Ewocar Burgundy Special Finishing Pad. Free of silicones and fillers; compatible with both rotary and dual-action polishers.
Fine Cut은 공격적인 연마 단계 이후 도장 표면을 마무리하기 위해 설계된 피니싱 컴파운드입니다. 홀로그램 자국, 미세 스크래치, 가벼운 흠집을 제거하며 10/10 광택 등급의 극도로 선명하고 깊이감 있는 미러 마감을 구현합니다. Ewocar 버건디 스페셜 피니싱 패드와 최적의 궁합을 자랑하며, 실리콘과 충전제가 없고 로터리 및 더블액션 폴리셔 모두 호환됩니다.
- Brand
- EWOCAR
- Categories
- Exterior : Polishes
Key features
- Finest finishing compound — lowest cut level in the Ewocar compound range
- Removes light scratches, haze, and hologram marks
- Delivers a 10/10 gloss rating with extremely clear, deep finish
- Best paired with the Ewocar Burgundy Special Finishing Pad
- Silicone-free and filler-free formula
- Compatible with rotary and dual-action polishers
Usage
- Ensure the paint surface is clean, dry, and free of contaminants before starting.
- Apply a small amount of Fine Cut to an Ewocar Burgundy Special Finishing Pad or a soft foam finishing pad.
- Set the polisher to a low speed (rotary: ~1000–1200 rpm; dual-action: ~3–4 on the dial) and spread the compound across the section with the machine off or at minimum speed to avoid product fling.
- Increase speed and work the section in overlapping passes until holograms, micro-marring, and light scratches are refined and a deep gloss emerges.
- Wipe off residue immediately with a clean microfiber cloth and inspect the finish under light.
핵심 특징
- Ewocar 컴파운드 라인업 중 가장 낮은 절삭력의 피니싱 컴파운드
- 가벼운 흠집, 흐림 현상, 홀로그램 자국 제거
- 10/10 광택 등급의 극도로 선명하고 깊이감 있는 마감 구현
- Ewocar 버건디 스페셜 피니싱 패드와 최적 조합
- 실리콘 및 충전제 미함유
- 로터리 및 더블액션 폴리셔 호환
사용법
- 작업 전 도장 표면이 깨끗하고 건조하며 오염물이 없는지 확인합니다.
- Ewocar 버건디 스페셜 피니싱 패드 또는 소프트 폼 피니싱 패드에 Fine Cut을 소량 도포합니다.
- 폴리셔를 저속(로터리: 약 1000–1200 rpm; 더블액션: 다이얼 3–4단)으로 설정하고, 컴파운드가 튀지 않도록 저속 또는 정지 상태에서 작업 구간 전체에 컴파운드를 펴 바릅니다.
- 속도를 높여 겹치는 패스로 작업 구간을 연마하며, 홀로그램 자국·미세 스크래치·가벼운 흠집이 사라지고 깊은 광택이 나타날 때까지 작업합니다.
- 깨끗한 극세사 타월로 잔여물을 즉시 닦아내고 조명 아래에서 마감 상태를 확인합니다.