1-Year Ceramic Spray Coating
1년 세라믹 스프레이 코팅
A spray-on ceramic coating built on an advanced silica resin base that delivers 1 year of hydrophobic protection with a 110° water contact angle, deep gloss, and chemical resistance after full cure. PFAS-free and usable on paint, glass, wheels, trim, PPF, vinyl, and matte finishes, with a fast 1-hour water-safe cure and coverage of 3–6 full vehicles per 3 oz bottle.
고급 실리카 레진 기반의 스프레이형 세라믹 코팅으로, 110° 수접촉각의 강력한 발수성과 깊은 광택, 내화학성을 1년간 유지합니다. PFAS 무함유 포뮬라로 도장, 유리, 휠, 트림, PPF, 비닐, 무광 마감 등 다양한 외부 표면에 안전하게 적용 가능하며, 도포 1시간 후 우천 노출이 가능합니다.
- Brand
- CLEAN.
- Categories
- Exterior : Coating
- pH
- neutral (7)
Key features
- 1-year ceramic protection via hybrid organic-inorganic silica film
- 110° water contact angle for sharp hydrophobic beading
- Ultra-high gloss and extreme slickness
- Water-safe in 1 hour at room temperature
- Chemical resistance pH 2–12 after 7-day full cure
- Multi-surface safe: paint, wheels, glass, trim, PPF, vinyl, matte
- PFAS-free formula
- 3–6 full vehicles per 3 oz bottle
Usage
- Wash the vehicle thoroughly and dry completely.
- Perform paint decontamination with an iron remover and clay towel if needed.
- If paint is faded or contains defects, carry out paint correction before coating.
- Remove polishing oils and residues with a panel prep spray and wipe clean with a microfiber towel.
- Spray the coating onto a microfiber towel or applicator and spread it over the surface in a cross-hatch pattern.
- Allow the product to self-level for 1–2 minutes, then remove any excess with a clean microfiber towel.
- An additional layer may be applied within 1 hour of the first application.
- Allow 1 hour of cure time before exposing the vehicle to water or rain.
핵심 특징
- 하이브리드 유-무기 실리카 필름의 1년 세라믹 보호
- 날카로운 발수 비딩을 위한 110° 수접촉각
- 극강의 광택과 매끄러움
- 상온에서 1시간 내 우천 노출 가능
- 7일 완전 경화 후 pH 2~12 내화학성
- 도장, 휠, 유리, 트림, PPF, 비닐, 무광면 다목적 사용
- PFAS 무함유
- 3oz 1병으로 차량 3~6대 시공 가능
사용법
- 차량을 깨끗하게 세차하고 완전히 건조합니다.
- 필요한 경우 철분 제거제와 클레이 타월로 도장 오염물을 제거합니다.
- 도장이 바래거나 스크래치·스월 마크가 있다면 코팅 전에 도장 교정을 진행합니다.
- 패널 프렙 스프레이로 폴리싱 오일과 잔여물을 제거하고 극세사 타월로 닦아냅니다.
- 코팅제를 극세사 타월 또는 어플리케이터에 적당량 분사하고 크로스 해칭 방식으로 표면에 고르게 펴 바릅니다.
- 1~2분간 자연 레벨링 후 잉여 제품을 깨끗한 극세사 타월로 제거합니다.
- 첫 번째 레이어 도포 1시간 이내에 추가 레이어를 적용할 수 있습니다.
- 물이나 비에 노출되기 전 1시간 이상 경화 시간을 확보합니다.