Ultra Shine Headlight Restoration Wipes
울트라 샤인 헤드라이트 복원 와이프
Armor All Ultra Shine Headlight Restoration Wipes use a simple two-step wipe process to remove oxidation, haze, and yellowing from headlights, restoring them to like-new clarity without tools or sandpaper. The UV sealant coating applied in step two cures in approximately three hours for lasting protection.
아머올 울트라 샤인 헤드라이트 복원 와이프는 간단한 2단계 와이프 과정으로 헤드라이트의 산화물, 흐림, 황변을 제거해 도구나 사포 없이 새것과 같은 투명도를 회복시킵니다. 2단계에서 도포하는 자외선 실란트 코팅은 약 3시간 후 경화되어 오래 지속되는 보호막을 형성합니다.
- Brand
- Armor All
- Categories
- Exterior : Polishes, Exterior : Glass Sealant
Key features
- Two-step restoration: removes oxidation then applies UV sealant
- Eliminates yellowing and haze caused by oxidation
- No tools or sandpaper required
- Pre-moistened wipes for precise application
- UV sealant cures in approximately 3 hours
Usage
- Apply painter's tape around the headlight to protect adjacent painted surfaces.
- Step 1 — Oxidation Removal: Confirm the headlight is clean and dry. Open one Cleaning/Oxidation Removal pouch and remove the wipe, keeping it folded to minimise evaporation.
- Scrub the headlight in a firm horizontal back-and-forth motion. Turn the wipe to a clean side as residue accumulates; continue until no residue transfers to the wipe.
- Open a second Cleaning/Oxidation Removal pouch and scrub with firm pressure for at least 2 more minutes. Discard used wipes. Repeat the full Step 1 sequence on the other headlight.
- Step 2 — UV Sealant Protection: Ensure the headlight surface is fully dry; wipe with a clean lint-free towel for best results.
- Open the UV Sealant Protection pouch and apply the wipe in one direction across the entire headlight, as if painting on a coat. One wipe covers both headlights.
- Allow the surface to cure undisturbed for approximately 3 hours (touch-dry); avoid touching or exposing to water until fully dry. If water spotting occurs before cure, repeat Steps 1 and 2 with fresh wipes.
핵심 특징
- 2단계 복원: 산화물 제거 후 자외선 실란트 코팅 도포
- 산화로 인한 황변 및 흐림 제거
- 도구나 사포 불필요
- 사전 적신 와이프로 정밀한 도포
- 자외선 실란트는 약 3시간 후 경화
사용법
- 헤드라이트 주변 도장 면을 마스킹 테이프로 보호합니다.
- 1단계 — 산화 제거: 헤드라이트가 깨끗하고 건조한지 확인합니다. 클리닝/산화 제거 파우치를 열고 와이프를 꺼내 증발을 줄이도록 접힌 상태를 유지합니다.
- 와이프로 헤드라이트를 좌우 방향으로 단단하고 고르게 문질러 산화 잔여물을 제거합니다. 잔여물이 쌓이면 와이프를 깨끗한 면으로 바꿔가며 잔여물이 더 이상 묻어나지 않을 때까지 계속합니다.
- 두 번째 파우치를 열고 최소 2분간 강하게 추가로 문지릅니다. 사용한 와이프는 버리고 반대쪽 헤드라이트도 1단계 전체를 반복합니다.
- 2단계 — UV 실란트 코팅: 헤드라이트 표면이 완전히 건조한지 확인하고 깨끗한 보풀 없는 타월로 한 번 더 닦습니다.
- UV 실란트 코팅 파우치를 열어 도장하듯 한 방향으로 헤드라이트 전체에 도포합니다. 와이프 한 장으로 헤드라이트 두 개를 모두 코팅할 수 있습니다.
- 약 3시간 동안 건드리지 말고 물과의 접촉을 피해 완전히 경화시킵니다. 경화 전 물 얼룩이 생기면 새 와이프로 1~2단계를 처음부터 반복합니다.
Also known as: 아머올, armorall, armor, 아머 올, Armor All Ultra Shine Headlight Restoration Wipes, USHRW, Armor All USHRW, 아머올 울트라 샤인 헤드라이트 복원 와이프
한국어로 보기