Adam's Salt, Mud & Grime Remover
아담스 솔트, 머드 & 그라임 리무버
Adam’s Salt, Mud & Grime Remover is a heavy-duty acidic wash formula engineered to loosen and lift salt deposits, caked mud, and road grime from the entire vehicle including the undercarriage. Its pH-based chemistry dissolves mineral-laden contamination that regular soaps leave behind. A thorough pre-wash step with this product prepares surfaces for a deeper, safer clean.
Adam’s Salt, Mud & Grime Remover는 일반 세차제로 제거하기 어려운 염분, 굳은 진흙, 도로 오염물을 산성 포뮬러로 강력하게 분해·제거합니다. 차체는 물론 하부까지 전반적인 세정에 사용할 수 있으며, 본격적인 디테일링 전 사전 세차 단계로 적합합니다.
- Brand
- Adam's Polishes
- Categories
- Exterior : Remover
- pH
- acid (3)
Key features
- Removes salt, mud, and road grime
- Acidic formula dissolves mineral contamination
- Suitable for full vehicle including undercarriage
- Deep-clean pre-wash application
- Works where regular soaps fall short
Usage
- Prepare two buckets with grit guards: one wash bucket with about 2 oz of product and a wash pad, and one rinse bucket with clean water.
- Rinse the vehicle thoroughly to remove loose surface contamination before beginning.
- Working top to bottom, dip the wash pad into the wash bucket and wash one section at a time.
- Rinse the pad in the clean rinse bucket after each section to prevent redepositing contamination.
- Rinse the entire vehicle with clean water once all sections have been washed.
- Inspect the surface and repeat any heavily soiled areas as needed.
- Dry the vehicle with a clean microfiber drying towel or forced-air dryer.
- Follow up with a full detail or protection step as desired.
핵심 특징
- 염분, 진흙, 도로 오염물 제거
- 산성 포뮬러로 미네랄 오염 분해
- 차체 하부 포함 전차량 사용 가능
- 디테일링 전 딥클린 사전 세차
- 일반 세차제가 닿지 못하는 오염 처리
사용법
- 그릿 가드가 있는 버킷 두 개를 준비하고, 세차 버킷에는 제품 약 2온스와 세차 패드를, 헹굼 버킷에는 깨끗한 물을 채웁니다.
- 세차 전 차량 전체를 충분히 물로 헹궈 표면의 느슨한 오염물을 제거합니다.
- 위에서 아래 방향으로, 세차 패드를 세차 버킷에 담근 후 한 구역씩 닦아냅니다.
- 각 구역을 닦은 후 패드를 헹굼 버킷에서 헹궈 오염물 재오염을 방지합니다.
- 모든 구역을 세척한 후 깨끗한 물로 차량 전체를 헹굽니다.
- 표면을 점검하고 오염이 심한 부분은 필요에 따라 반복 세정합니다.
- 깨끗한 극세사 건조 타월 또는 에어 드라이어로 차량을 건조합니다.
- 필요에 따라 디테일링 또는 보호 코팅 작업을 후속으로 진행합니다.